SSR9 Upgrades

Hand picked upgrade parts specifically compatible with SSR9 to make it even better!

    14 products

    Sold Out
    Titan II ETU upgrade part for airsoft replica in packaging
    Opened box for Titan II mosfet showing what's included in the kit
    closeup of Titan II ETU MOSFET unit from top side
    closeup of Titan II rear wired V2 gearbox AEG version motor cables
    closeup of Titan II for V2 gearbox AEG version battery connector
    GCS App for configuring Titan II ETU and G5 Smart Brushless motor
    Gate Titan II for V2 AEG / Rear wired
    GATE
    €146.00
    Sold Out
    Gate G5 Smart brushless airsoft motor long type from front
    Gate G5 Smart brushless airsoft motor long type showing its pinion gear with d-shaft
    Gate G5 Smart brushless airsoft motor long type from back showing it's connection terminals
    GCS app showing the G5 Smart Brushless Motor on the list of connected devices
    GCS app showing configuration options like speed and torque for Gate G5 Smart Brushless motor
    Gate G5 Smart Brushless Motor / Long
    GATE
    €195.00
    Gate EON Gear Set high speed 13:1 ratio with short stroked sector gear, cnc machined
    Top-down view of Gate EON 13:1 gears showing the SSG-4T short stroked sector gear marking
    Gate EON Gear Set 13:1 / Short Stroked
    GATE
    €36.00
    Orange 4UANTUM Friction Pro AEG bucking with embossed logo and the soft flat nub beside it
    Bore view of the 4UAD AEG bucking showing the single-point flat nub and alignment tab inside
    4UANTUM Friction Pro bucking installed over the window of a stainless AEG inner barrel
    4UANTUM Friction Pro Bucking for AEG
    4UAD
    €11.00
    Sold Out
    Gate Tacticker realistic trigger pull mechanism for airsoft replica
    Gate Tacticker realistic trigger pull mechanism for airsoft replica installed in SSR4 Mk1 with Novritsch ETU
    Close-up of Gate Tacticker clicker module mounted beside the trigger on a V2 gearbox ETU
    Gate Tacticker / Realistic Trigger Clicker
    GATE
    €34.00
    4uantum heat resistant gearbox lubricant by 4UAD Smart Airsoft
    tip of 4uantum heat resistant gearbox lubricant pen by 4UAD Smart Airsoft
    4UANTUM Gear / Gearbox Lubricant
    4UAD
    €8.00
    20pcs of airsoft gearbox shims in 0.3mm thickness
    20pcs of airsoft gearbox shims in 0.1mm thickness
    Gearbox Shim Set (20pcs)
    FPS Softair
    €5.00
    Sold Out
    Pair of Gate Titan II HPA conversion cables with solenoid and ETU plug connectors
    Gate Titan II / AEG to HPA Conversion Cables
    GATE
    €9.00
    inner barrel stabilizer for novritsch supressor#size_34-37mm
    inner barrel stabilizer for novritsch supressor#size_34-37mm
    inner barrel stabilizer for novritsch supressor#size_34-37mm
    inner barrel stabilizer for novritsch supressor#size_34-37mm
    inner barrel stabilizer for novritsch supressor#size_34-37mm
    inner barrel stabilizer for novritsch supressor#size_29-33mm
    inner barrel stabilizer for novritsch supressor#size_29-33mm
    inner barrel stabilizer for novritsch supressor#size_29-33mm
    inner barrel stabilizer for novritsch supressor#size_29-33mm
    inner barrel stabilizer for novritsch supressor#size_29-33mm
    Inner Barrel Stabilizer (Suppressor / Outer Barrel)
    TRIDOS.DESIGN
    €12.00
    Side profile of the low profile canted picatinny rail showing its 30 degree angle
    Offset red dot sight on the canted rail beside the main scope of an airsoft sniper rifle
    Front view of the canted sight mount holding a red dot clear of the rifle's scope
    Empty canted rail section mounted on the receiver's top picatinny rail
    Close-up of the canted rail mount clamped to the top picatinny with two grub screws
    CNC aluminum canted picatinny rail seen from above, showing its accessory slots
    Underside of the offset picatinny rail showing the clamp channel and two grub screws
    Canted 30° Picatinny Rail
    FMA
    €11.00
    Black 1.5 inch high red dot mount standing alone, showing its skeletonized riser design
    Victoptics red dot sitting on the tall riser mount, clamped to a rifle's top rail
    Side profile of the elevated red dot mount raising a Victoptics sight above the rail
    Shooter's eye view through a red dot raised 1.5 inches over the picatinny rail
    Red dot with honeycomb filter on the 1.5 inch mount, seen from the front quarter
    Top plate and picatinny clamp of the red dot riser with its two mounting screws
    Top face of the high mount showing screw holes, recoil stop and lightening slots
    1.5" High Red Dot Mount
    Vector Optics
    €18.00
    Black red dot lens protector ring clamped on the objective of a Victoptics sight
    Victoptics red dot sight on a riser mount with the protector ring around the front lens
    Red dot protector clamp ring with hex screw and the included allen key
    Red Dot Lens Protector by Vector Optics
    Vector Optics
    €8.00
    New
    Vector Optics Maverick 1x22 Gen2 red dot sight with QD riser mount, front-left view
    Maverick Gen2 red dot mounted on an M4 airsoft AEG rifle via the QD picatinny mount
    Close-up of the Maverick Gen2 numbered brightness dial, capped turrets and coated lens
    Maverick 1x22 Gen2 with UP elevation turret, brightness ring and QD lever mount visible
    Sharp 3 MOA aiming dot visible through the lens of the Maverick 1x22 Gen2 red dot sight
    Open CR2032 battery compartment on the Maverick Gen2 red dot with its coin-slot cap removed
    Maverick Gen2 red dot with included low-profile mount and hex tool for airsoft setups
    VectorOptics Maverick 1x22 Red Dot Gen2
    Vector Optics
    €65.00
    New
    Flamingo AEG bucking fitted over the hop-up window end of a stainless steel inner barrel
    Pink Flamingo bucking for AEG standing upright, showing its large flat contact patch
    Front view of the Flamingo AEG bucking showing the feed lips and inner bore
    Flamingo Bucking for AEG
    Sniper Mechanic
    €12.00